Diagnostic Tool

You can use the Diagnostic Tool (prepare > Post-Processing Tools > Tri-mesh Tools) to run multiple quality tests on the tri-meshes contained in your surface set. The Diagnostic Tool can find different types of issues within the surface set which might give you unexpected results during subsequent modeling steps or could impact the quality of final maps. The tool lists all issues in a table and opens a dedicated Diagnostic View where all the issues are highlighted. You can use the table to set the focus in the Diagnostic View on one issue and look at the issues found one by one. The table also provides the surface type and TVDSS information about the issue which can be used to search and filter relevant issues. The best way to prevent and solve such issues is to use the tri-mesh tools, or solve them manually using the editing tools. You can also review the quality of the triangles belonging to your tri-mesh by displaying any of the Mesh Quality properties, available in the context menu of a tri-mesh (Properties > Default Geometry Properties > Mesh Quality).

How to use the diagnostic tool

  1. On the Diagnostic Tool form, in the Model drop-down list, select the model that contains the tri-meshes that you want to check for issues.
  2. Under Tests, select the issue(s) you want to test the model for. For more information about the different tests, see below.
  3. Click Run Tests. After running the test(s), the results can be analyzed in the Test Results table and a dedicated Diagnostics view.
    • The issues that were found are listed (per category) in the Test Results table at the right side of the form. The table has three columns - first column shows the Issue name, second column shows the respective surface Type and the third column shows the respective depth in TVDSS for the listed issue. Use the column headers to sort the test results, or use the context menu to search and filter the results. The results are grouped in test type, and by default each test type is sorted on surface type followed by the issue name.
    • A dedicated Diagnostic View is opened, displaying all the tri-meshes with issues.
  4. In the table, select the tri-mesh or issue that you want to highlight in the Diagnostic View. Only selected tri-mesh(es) are visualized.
  5. Use either the tri-mesh tools (prepare > Post-Processing Tools > Tri-mesh Tools, only for tri-meshes in surface sets), the structure builder tools (under the Structure Builder button of the strip that you are working in) or the editing tools (Workspace > Tools) to solve the issues. Rerun the test(s) and check if the issues are corrected to your satisfaction.
  6. Click Close to close the form. This will also close the Diagnostic View.

If the edited model is already used in subsequent modeling steps, you have to rerun these modeling steps as well.

Selecting a test

Folded edges  The tri-meshes of your model should not have sharp bends or kinks. Bends are measured via the angle between two adjacent triangles. All triangles with an angle below a maximum specified by you are considered folded and will show up in the results list. The two triangles creating this angle are highlighted in red in the dedicated Diagnostic View.

For more information, see Folded edges.

The two triangles that are creating a folded edge are highlighted in red in the Diagnostic View.    click to enlarge

Flat triangles  Very spiky, elongated triangles may cause unstable results in different processing steps. Flat triangles are measured via the angle between two triangle edges. All triangles with an angle below a maximum specified by you are considered flat triangles and will show up in the results list. The triangle is highlighted in red in the dedicated Diagnostic View.

For more information, see Flat triangles.

Flat triangles introduced close the edge of a fault due to the surface resampling. In this scenario you can use the Remove Node tool to resolve the issue.    click to enlarge

Internal boundaries  An internal boundary is formed when a tri-mesh contains a gap, which is the case when the edges of one or more triangles are not connected to other triangles. This test identifies and locates these edges. Fault gaps in structural model horizons, when they are watertight in the respective horizon-fault combination, are recognized by the diagnostic tool as 'correct' and will not be flagged as internal boundaries. Ideally, every tri-mesh should be continuous and free of any gaps. Gaps in your faults may not segment your model in a consistent way and local flexures and artifacts in subsequent modeling steps can be the result. All the internal boundaries of the tri-mesh are highlighted in red in the Diagnostic View. For more information, see Internal boundaries.

Intersection quality   The test analyzes the surface boundaries and color-codes the boundaries and its nodes to give visual feedback. You can run the intersection quality test on the surfaces in your surface set, but during subsequent modeling steps your surfaces might have been re-triangulated which can result in different tri-meshes. The issues found can be viewed in the dedicated Diagnostic View. You can use the Extend to Other Surfaces tool to solve the issue(s).

Example in which the tool identified a free boundary section. Both the segments and the nodes are highlighted in orange.    click to enlarge